Edit vector strokes and fills
Verification record: Umoupen 0.9.62 build 662 (2026-10-22) · Verification scope
A vector stroke is line data with an editable width and curve. A fill describes an area’s shape and color and can be selected separately from its lines. Select strokes and fills separately on a Vector Layer, then revise their shape, color, and connections. These controls do not edit Raster pixels.
Location: Left toolbar → Move Tool → Options on the right
Choose the selection target first
Section titled “Choose the selection target first”- Make a Vector Layer active.
- Choose Move or Lasso.
- In Options, target strokes when editing lines or fills when editing areas.
- Start by selecting one stroke or fill and confirm the selection highlight.
Edit a stroke
Section titled “Edit a stroke”- Select a line with
Stroke Selection. - Adjust Curve Area when connected curves also need to change.
- Change the stroke shape, width, or color.
- Confirm that unselected strokes and fills did not change.
Shape stroke width with the Taper Tool
Section titled “Shape stroke width with the Taper Tool”Use the Taper Tool to shape the width of a Vector stroke and how it narrows at the endpoints.
- Select a stroke on a Vector Layer.
- Select the Taper Tool.
- Drag on the stroke to adjust its width and taper.
- Check the endpoints and the width through the middle of the stroke.
The developer’s 0.9.60 announcement says the layer-wide 1px toggle was removed and replaced by a stroke property. The new control location and its effect on taper were not verified in this session.
Edit a fill
Section titled “Edit a fill”- Select an area with
Fill Selection. - Change its color or shape.
- Confirm that surrounding strokes were not selected unintentionally.
Use Line to Fill when you need to edit a stroke as a filled shape. Duplicate the layer first, then confirm that the result can be selected as a fill instead of a stroke.
Choose a fill brush drawing mode
Section titled “Choose a fill brush drawing mode”Choose the drawing mode for new fills in the brush Options.
- Make a Vector Layer active.
- Select
Fill Circlewith Brush, then open Options. - Choose one of the four icons beside Type: Fill. From left to right, they are Over Lines, Under Lines, Inside Fills, and Behind Fills.
The selected icon is highlighted blue, and its tooltip shows its name. The drawing results where strokes and fills overlap have not been verified for these modes.
Replace colors in selected vector content
Section titled “Replace colors in selected vector content”- Select the Vector strokes or fills whose color should change.
- Open Replace Color in Options and set the source and replacement colors.
- Choose the scope: current frame, layer, shot, or file.
- Apply the replacement and confirm that only the selected Vector content in that scope changed.
Raster pixels are not included. Test the current frame before applying the replacement to a wider scope.
If you cannot select the target or too much changes
Section titled “If you cannot select the target or too much changes”| Symptom | Check this first |
|---|---|
| A stroke or fill cannot be selected | Confirm that the active layer is Vector and that Options targets strokes or fills. |
| Artwork on another layer is selected | Limit the selection scope to Selected Layers. |
| Connected strokes move too | Reduce Curve Area and test with one stroke. |
| The shape breaks at an intersection | Undo, then edit the intersection in smaller parts. |
You cannot return to stroke editing after Line to Fill | Return to the duplicated source layer or undo before saving. |
Main options
Section titled “Main options”| Option | What it does |
|---|---|
| Stroke Selection | Selects a stroke so you can edit its width, color, and curve. |
| Fill Selection | Selects an area so you can edit its color and shape. |
| Curve Area | Adjusts the area around connected curves. |
| Line to Fill | Converts a line into a filled shape. |
| Taper Tool | Adjusts a Vector stroke’s width and endpoint taper. |
| Over Lines / Under Lines / Inside Fills / Behind Fills | Drawing modes selected for a Vector fill brush. |
| Replace Color | Replaces a color in selected Vector content across the frame, layer, shot, or file. |
Related articles
Section titled “Related articles”Verification
Section titled “Verification”- Hands-on verified: On a Vector Layer, checked the four drawing mode icons for Fill Circle (Type: Fill), their tooltips from left to right (Over Lines, Under Lines, Inside Fills, Behind Fills), and the blue highlight when selected. This row of four icons was not displayed for Solid Hairline (Type: Solid).
- Unverified: The drawing results for each mode, transparency and overlapping strokes and fills, the affected layer scope, the article’s other vector editing operations, saving/reopening, and Windows/iPad were not verified in build 662.
- Evidence records: F-20261022-501